The design of the analog circuit is the most painful but deadly design part of the engineers! It summarizes the issues that should be noted in the analog circuit design, not bad, turn around and share with everyone.
(1) In order to obtain a feedback circuit with good stability, it is usually required to use a small resistor or choke outside the feedback loop to provide a buffer for the capacitive load.
(2) The integral feedback circuit usually requires a small resistor (about 560 ohms) in series with each integrating capacitor greater than 10pF.
(3) Do not use active circuits outside the feedback loop to filter or control the EMC's RF bandwidth, but only passive components (preferably RC circuits). The integral feedback method is effective only when the open loop gain of the op amp is greater than the closed loop gain. At higher frequencies, the integration circuit cannot control the frequency response.
(4) In order to obtain a stable linear circuit, all connections must be protected using passive filters or other suppression methods such as opto-isolation.
(5) Use an EMC filter and the IC-related filters should be connected to the local 0V reference plane.
(6) Input and output filters should be placed at the connection of the external cable. Any wire connection inside the shielded system is required for filtering because of the antenna effect. In addition, filtering is also required at the wire connections inside the shield system of the converter with digital signal processing or switching mode.
(7) High quality RF decoupling is required on the analog IC's power and ground reference pins, just like digital ICs. However, analog ICs typically require low frequency power supply decoupling because the power supply noise rejection ratio (PSRR) of the analog components increases little after being above 1 kHz. RC or LC filtering should be used on the analog power traces of each op amp, comparator, and data converter. The corner frequency of the line filter should compensate for the PSRR corner frequency and slope of the device to achieve the desired PSRR over the entire operating frequency range.
(8) For high-speed analog signals, transmission line technology is necessary depending on the connection length and the highest frequency of communication. Even with low frequency signals, the use of transmission line technology can improve its immunity to interference, but transmission lines that do not have the correct match will have an antenna effect.
(9) Avoid using high-impedance inputs or outputs that are very sensitive to electric fields.
(10) Balanced transmit and receive (differential mode) techniques are used in analog circuits since most of the radiation is generated by common mode voltages and currents, and because electromagnetic interference in most environments is a common mode problem. It will have good EMC performance and reduce crosstalk. The balanced circuit (differential circuit) drive does not use the 0V reference system as a return current loop, thus avoiding large current loops and reducing RF emissions.
(11) The comparator must have hysteresis (positive feedback) to prevent erroneous output changes due to noise and interference, and to prevent oscillation at the trip point. Do not use a comparator that is faster than needed (keeping the dV/dt within the required range, as low as possible).
(12) Some analog ICs are inherently sensitive to RF fields, so it is often necessary to shield such analog components using a small metal shielded box mounted on the PCB and connected to the ground plane of the PCB. Be careful to ensure its heat sink.
N Series Ground Screw/Ground Screw pile,ground Spike,ground screw pile foundation ,screw pile :Threaded Bolts fasten, No Flanges,one ,three or four bolts fixed .Including not galvanized ground screw,hot dip galvanized ground screw.
Available in the following diameters and length :
Diameter :68 mm,76 mm,89 mm,114 mm ,140mm,219mm
Length of N Ground Screw pile (mm) : 800,1000,1200,1500,1800,2000,2500,3000,5000 and requested length
Nut aperture for N series ground screw : 3-M 10/12/14/16
Surface treatment : Hot Dip Galvanized ,DIN EN ISO 1461-1999 ,average thickness of coating more than 80 micron
Range of Application : Solar power system,fence, timber construction ,farm and garden fence ,umbrella basement ,advertising board and banner ,lighting pole &
Production charting : Cutting pipe to he standard length ,forming the pipe according to design ,welding and assemble blade,flange,nut , acid pickling ,hot dip galvanize ,QC, Packing ,shipments
N Series Ground Screw
Helix Ground Screw,Helical Ground Screw,Solar Mounting Ground Screw,Galvanized Steel Ground Screw,Helical Screw Piles
BAODING JIMAOTONG IMPORT AND EXPORT CO., LTD , https://www.chinagroundscrew.com