Figure 1 shows an audio Panpot circuit that responds to the setting of the potentiometer by continuously changing the position of the mono audio signal between the left and right stereo channels. Low cost and low distortion are important considerations for audio circuits. The dual-channel low-distortion differential amplifier AD82731 uses internal gain setting resistors to ensure excellent matching between the two channels. It requires no external components, and each channel is configured as two high-performance amplifiers with a gain of 3. In the audio frequency range, the total harmonic distortion is less than 0.0007%.
Although this circuit can be built in a discrete manner, integrating amplifiers and resistors on a single chip can bring many benefits to circuit board designers, such as better performance specifications, smaller PCB area, and lower production costs.
Figure 1. Audio Panpot amplifier
In this circuit, the signal is distributed between the two amplifiers through a 10 kΩ series resistor. Insert a vernier grounded potentiometer between the two non-inverting inputs. The combination of a potentiometer and a 10 kΩ resistor constitutes a light load and is easily driven by most signal sources. The gain configuration of the amplifier is 3. When the potentiometer cursor is located at either end, one input terminal is grounded, so no signal is transmitted to the corresponding output terminal. The voltage at the other input is VIN / 2, so its output is 1.5 & TImes; VIN. When the cursor is in the middle position, the input of both amplifiers is VIN / 3, so the output of each amplifier is VIN. In this way, by moving the cursor (either mechanically or electronically), the signal level on one channel changes continuously from 0 to 1.5 & VIN, and the signal level on the other channel changes continuously from 1.5 & TImes; VIN to 0. To the listener, the sound source seems to move from one channel to another between sound levels. Therefore, the sound image or the apparent source of sound can be located anywhere between the left and right speakers.
Figure 2. Total harmonic distortion and noise versus frequency
Figure 2 shows the total harmonic distortion and noise over the entire audio range. The error becomes larger as the frequency increases, but the total error at 20 kHz is still less than 0.0007%. Figure 3 shows the connection diagram of the IC.
1.ANTENK Card Edge Connectors are precision engineered PCB mount connectors developed to mate with the plated fingers of a printed circuit daughter board. Their bifurcated, cantilever contacts are set in a dual readout configuration and they offer a reliable connection for a wide range of PCB thicknesses. ANTENK`s sturdy solder tails with tapers allow easy insertion and rugged durability
Card Slot Connectors Specification:
*Electrical Characteristitics:
Current Rating;0.5A.
Withstanding Voltage:AC500V r.m.s.
Insulation Resistance:1000Megohms Minimum at DC 500V
Contact Resistance:100Miliohms Maximum.
*Mechanical Characteristics:
Mating Cyeles:5000 Insertions.
*Environmwntal:
Operating Temperture:-40°To+60°
*Material:
1.Housing:HI-Temp plastic UL 94V-0 Rated.
2.Contact:Copper Alloy.
3.Shell:SUS.
*Finish :
1u" Gold plated on conatct area,1u" Gold plated on
solder tails, Base Nickel :50u"Min
*Packing:
Number of connectors:750Pcs/REEL
MATERIAL&FINISH
Insulator:PBT Glass Fiber(UL94V-0)
contact:Brass
Contact:Gold-Plated Over Nickel
SPECIFICATIONS
Current Rating:1A AC,DC
Voltage Rating:250V AC,DC
Temperature Range:-40℃ To+105℃
Contact Resistance:20mΩMin
Insulation Resistance:1000MΩ Min
Withstanding Voltage:500V AC/Min
Video Card Connectors,Card Slot Connectors,Card Edge Slot Connectors,CF Card Connector, Edge Card Connector,Memory Card Connector,PC Card Connector,SIM Card Connector,Smart Card Connector
ShenZhen Antenk Electronics Co,Ltd , https://www.pcbsocket.com